Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ASCEND) Forcing an IP address
ThanX,
I tried that, It work fine , but, I have Pipeline routers connecting to this max as well.
When I put that seting to YES, I have to set the Framed-Address setting in the radius user's profile for them (pipeline routers) to connect, and when they do connect, the get the ip assigned to them but cannot go on the internet, the MAX doesn't create any routes for them.
any Ideas ?
At 12:29 PM 9/23/98 -0700, Kevin A Smith wrote:
>Also on the MAX set the parameter:
>Ethernet/Mod config/WAN options.../Pool only=Yes
>
>At 06:42 AM 9/22/98 , Tim Connolly wrote:
>> I think your problem is in the way you have PPP configured on your
>>Linux box. You didn't give much info below, but I bet if you setup is
>>anything close to "default" you will find a few commands at the bottom
>>of the /etc/ppp/options file which explains how PPP decides whether to
>>use the host assigned address or its own. I believe these two lines are
>>commented out by default (and should be in my oppinion), but you may try
>>uncommenting them and see if that helps any. good luck!
>>
>>Frantzcy Paisible wrote:
>>
>>> Hi all,
>>>
>>> Here is this week's "My Max is acting up" message:
>>>
>>> Maybe you encountered this one already...
>>>
>>> I have a linuxbox with an ethernet card and a modem.
>>> The ethernet card as the local address 192.168.0.1.
>>> The linuxbox connects to the max using a 28.8 modem.
>>>
>>> The max will not give the linuxbox an IP from it's pool,
>>> It will leave the linuxbox with the IP number of the
>>> ethernet card (192.168.0.1), not with of of the pool.
>>>
>>> I've tried but I can't force it with Framed-Address, it
>>> gives me an error 101 and disconnects the call.
>>>
>>> On the linuxbox, I tryied the 0.0.0.0:0.0.0.0 option, no
>>> success.
>>>
>>> I had the exact same problem with a Pipeline, it wasn't
>>> considered as a problem since that was the way I wanted
>>> it to work.
>>>
>>> How can I get around that problem ?
>>>
>>> Frantzcy
>>>
>>> --
>>> "If your desktop is full, increase your resolution!"
>>> "No more space on your screen for POST-ITs, get a bigger screen"
>>>
>>> Frantzcy Paisible
>>> frantzcy@mtl.net
>>> ++ Ascend Users Mailing List ++
>>> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
>>> To get FAQ'd: <http://www.nealis.net/ascend/faq>
>>
>>-- Tim Connolly tec@mountain.net MountainNet, Inc.
>>-- (304) 594-9075 ext. 37 2816 Cranberry Square
>>-- fax (304) 594-9088 Morgantown, WV 26505
>>
>>
>>++ Ascend Users Mailing List ++
>>To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
>>To get FAQ'd: <http://www.nealis.net/ascend/faq>
>>
>
>Kevin Smith (kevin@ascend.com)
>Ascend Communications...
> ...where Network Solutions never end.
>
--
"If your desktop is full, increase your resolution!"
"No more space on your screen for POST-ITs, get a bigger screen"
Frantzcy Paisible
frantzcy@mtl.net
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>
References: