Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ASCEND) NAT Help - 1st experience
At 01:58 AM 3/25/98 -0800, you wrote:
>At 05:01 PM 24/03/98 -0800, you wrote:
>>I need a bit more guidance on this issue....
>>
>>
>>At 11:31 PM 3/23/98 -0800, you wrote:
>>
>>>So, here's how it should look:
>>>
>>>My Addr=<IP ADDRESS OF INTERNAL LAN, or in your words illegal address>
>>Okay, fine
>>
>>>Rem Addr=<VALID IP ADDRESS>
>>Which valid IP address? The remote end's ip (my MAX) or the LEGAL address I
>>want NAT to use?
>
>The legal address you want NAT to use.
Then how does the Pipe route to the MAX? The Rem Addr must contain a route
to the remote side of the connection, right?
>
>
>>
>>>Not sure how to configure the Max side, because I have no experience with
>>>it.
>>Does anyone know how to set up the MAX side?
>
>Can someone shed some light on this please? I have no experience with the
Max.
>
>>The manual for the Pipeline says that the MAX must assign a dynamic
>>address. Is this true? So every time the connection is established, NAT
>>potentially uses a different address (single IP translation used)?
>
>No. It can be a static IP. I know this, because my ISP gives me a static
>IP, and NAT works great. Although, NAT doesn't care.
>
>>>
>>>Regards,
>>>
>>>* T0uchT0ne #
>>>
>>>
>>>At 06:41 PM 23/03/98 -0800, you wrote:
>>>>Haven't had a need to set up NAT, but came across a client site that
>>>>already has an existing illegal scheme that they insist on keeping.
>>>>
>>>>Here's the config:
>>>>
>>>>My end: Max2024 - 6.0
>>>>Client end: Pipe 50 - 5.1A
>>>>connection: ISDN
>>>>
>>>>I turned on NAT/single IP on the P50. My question is, what do I set the
>>>>Pipeline's IP Address to be - an illegal address (192.168.100.254/24) or a
>>>>legal address (198.145.76.97/26)? Can I just give it a second address -
>>>>i.e, IP Addr=198.145.76.97/26 and 2nd Address=192.168.100.254 so I can
>>>>still telnet to it from my side?
>>>>
>>>>what do I set the LAN Address to on the MAX side of the connection?
>>>>
>>>>I guess if someone could just explain exactly what I need to do to make
>>>>this work, I'd be set.
>>>>
>>>>Thanks,
>>>>
>>>>
>>>>
>>>>
>>>>
>>>>| M a r k B r o d y |
>>>>| Opus Creative Group Inc. |
>>>>| Portland, Oregon USA |
>>>>++ Ascend Users Mailing List ++
>>>>To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
>>>>To get FAQ'd: <http://www.nealis.net/ascend/faq>
>>>>
>>>
>>
>>
>>
>>| M a r k B r o d y |
>>| Opus Creative Group Inc. |
>>| Portland, Oregon USA |
>>++ Ascend Users Mailing List ++
>>To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
>>To get FAQ'd: <http://www.nealis.net/ascend/faq>
>>
>
| M a r k B r o d y |
| Opus Creative Group Inc. |
| Portland, Oregon USA |
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>
References: