RE: (ASCEND) P130 and T1

[Steve LaDuke <steve_laduke@tuttle.com>]

I have been using a P130 [5.1A] for 4 months.  I have a T1-Frame Relay 
connection to a Cisco 2501 [11.0(4)].  I have had no problems.

Steve LaDuke.

> -----Original Message-----
> From:	Richard Johnsson [SMTP:johnsson@interval.com]
> Sent:	Sunday, January 25, 1998 12:36 PM
> To:	ascend-users@max.bungi.com
> Subject:	Re: (ASCEND) P130 and T1
> 
> I have six P130's connected to T1 frame relay at both full T1 and sub
> rate
> port speeds. No problems. The oldest have been in use since the P130
> was
> first available.
> 
> At 12:13 PM 1/25/98 -0800, Terrelle Shaw wrote:
> >We have been using the P-130 on our T1 for over 2 years. the only
> gripe i
> >have is sometimes when i telnet to the router, it causes a
> >reboot. Pisses me off, cause with our telco, the line doesn't come
> back up
> >for at least 3+ mins. Our telco has a cisco on the other end.
> >Plus were bridging the p130 with another p-130 so i have to turn that
> >connection profile off, so the line can come back up AT ALL, AND MOST
> of
> >the time when this reboot happens it looses it default route so i
> have to
> >completely remove the default route, put something in there..
> reboot.. then
> >change it back..( crazy huh?)
> >But other than that.. i have no CRC errors or anything.. ( I just
> don't
> >telnet into it often) Hehehehe.. but all these things might be
> because
> >were running 4.6A.. will upgrade soon.. maybe it would clear that
> >telnet rebooting problem and lost of default route problem..
> >
> >
> >At 12:06 PM 1/25/98 -0600, Miles Lott wrote:
> >>Well, that is the answer I didn't want to hear:)  Hopefully, there
> >>are some successful installs out there?  I suppose we could try to
> >>make a case for an exchange since we bought this through the ISP.
> >>Or we could jump off to another service with the Cisco/ADC setup.
> >>I can't see continuing with this if it will not be reliable at T1
> >>speeds.
> >>TTYL
> >>
> >>On Sun, 25 Jan 1998, Bob Roswell wrote:
> >>
> >>> We had  a customer using the P-130s on a T-1 Line. and switched to
> >Cisco's. 
> >>> The P-130 is much more cost effective particularly if you want and
> ISDN 
> >>> backup....
> >>> But the rock solid reliability is not there.  With the P-130's we 
> >>> intermittently get a huge number of CRC errors.  Rebooting one or
> the 
> >>> other P-130's
> >>> fixed the problem -- until it reappeared.  Since we went with
> Cisco
> >Routers 
> >>> and ADC Kentrox CSU's, we have had zero problems.
> >>> Bob Roswell
> >>> broswell@syssrc.com
> >>> 
> >>> ++ Ascend Users Mailing List ++
> >>> To unsubscribe:	send unsubscribe to
> ascend-users-request@bungi.com
> >>> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >>> 
> >>
> >>++ Ascend Users Mailing List ++
> >>To unsubscribe:	send unsubscribe to
> ascend-users-request@bungi.com
> >>To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >>
> >>
> >
> >++ Ascend Users Mailing List ++
> >To unsubscribe:	send unsubscribe to
> ascend-users-request@bungi.com
> >To get FAQ'd:	<http://www.nealis.net/ascend/faq>
> >
> >
> ++ Ascend Users Mailing List ++
> To unsubscribe:	send unsubscribe to
> ascend-users-request@bungi.com
> To get FAQ'd:	<http://www.nealis.net/ascend/faq>
++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>

---

Follow-Ups:

• RE: (ASCEND) P130 and T1
• From: Miles Lott <milos@insync.net>

---

• Prev by Date: Re: (ASCEND) way to get into MAX
• Next by Date: Re: (ASCEND) way to get into MAX
• Prev by thread: Re: (ASCEND) P130 and T1
• Next by thread: RE: (ASCEND) P130 and T1
• Index(es):
  • Main
  • Thread