Re: (ASCEND) Dial out Problem

["Dave Joyce" <Dave.Joyce@rtc1.com>]

How do you change the port speed when it has to do with the Telnet speed? It
is auto detect, isn't it?

Dave Joyce
Internet Manager
RTC on Line
219-223-0228
FAX 219-223-4898

----- Original Message -----
From: Buckner, John <BucknerJohn@bfusa.com>
To: 'Dave Joyce' <Dave.Joyce@rtc1.com>; Scot Tucker <STUCKER@mvnhealth.com>;
<phiber@polar.negation.net>
Cc: <ascend-users@bungi.com>
Sent: Tuesday, August 17, 1999 12:41 PM
Subject: RE: (ASCEND) Dial out Problem


> Have you tried slowing your modem port speed to 38.4?  I have a router hop
> between my Ascend and I had to slow down port speed.
>
> -----Original Message-----
> From: Dave Joyce [mailto:Dave.Joyce@rtc1.com]
> Sent: Tuesday, August 17, 1999 9:36 AM
> To: Scot Tucker; phiber@polar.negation.net
> Cc: ascend-users@bungi.com
> Subject: Re: (ASCEND) Dial out Problem
>
>
> I can dial out using a Max 2012 but it was a lot of jumping around until
it
> worked.
>
> Now when we connect to a remote computer it will respond fine and then all
> of a sudden just stop responding, maybe after 10 or so keystrokes, wait
> about 15 seconds and you get to use another 10 or so keystrokes.
>
> I was trying to use this outbound network modem to connect our accounting
> people with the BBS banking system, but with the constant delays it is too
> frustrating to use. It doesn't seem to be DeskDials fault as this symptom
> occurs when in a direct telnet session doing the open command.
>
> Is there anyone one has information on the solution or do we just scrap
the
> Max's for outbound calls?
>
> Dave Joyce
> Internet Manager
> RTC on Line
> 219-223-0228
> FAX 219-223-4898
>
> ----- Original Message -----
> From: Scot Tucker <STUCKER@mvnhealth.com>
> To: <phiber@polar.negation.net>
> Cc: <ascend-users@bungi.com>
> Sent: Tuesday, August 17, 1999 7:40 AM
> Subject: Re: (ASCEND) Dial out Problem
>
>
> > Our lines are configured for 2way; is there any thing else we can do?
> >
> > Scot Tucker - Networking Support
> > Network Data Systems
> > (315) 792-1057
> > fax (315) 792-1070
> > mailto:stucker@mvnhealth.com
> >
> > >>> Chris Rogers <phiber@polar.negation.net> 07/30/99 05:20PM >>>
> > Is the T1/PRI circuit that the MAX is using a DID or 2way?  If its a
DID,
> > you will not be able to place out bound calls, and the MAX box wont
> > exactly tell you that.  Hope this helps some,
> >
> > -chris
> >
> > On Fri, 30 Jul 1999, Scot Tucker wrote:
> >
> > > We have an ascend max 4002 and we can't dial out with it at all. When
we
> > > try to open a available modem ie ascend% open 3:1, we get the server
> > > ready message with the port we're using. We can enter at commands and
> > > get OK responces but when we try to dial out it doesn't work on any
> > > modem. It doesn't even try to take the modem off hook.
> > >
> > > If someone could help, I would be very grateful. The Ascend Max 4k
just
> > > got a Ease of Setup award, but it hasn't been easy for us at all!
> > >
> > > Thank you
> > >
> > >
> > > Scot Tucker - Networking Support
> > > Network Data Systems
> > > (315) 792-1057
> > > fax (315) 792-1070
> > > mailto:stucker@mvnhealth.com
> > >
> > > ++ Ascend Users Mailing List ++
> > > To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> > > To get FAQ'd: <http://www.nealis.net/ascend/faq>
> > >
> >
> > ++ Ascend Users Mailing List ++
> > To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> > To get FAQ'd: <http://www.nealis.net/ascend/faq>
> >
> > ++ Ascend Users Mailing List ++
> > To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> > To get FAQ'd: <http://www.nealis.net/ascend/faq>
>
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <http://www.nealis.net/ascend/faq>
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <http://www.nealis.net/ascend/faq>

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>