RE: (ASCEND) Dial out Problem

["Buckner, John" <BucknerJohn@bfusa.com>]

Have you tried slowing your modem port speed to 38.4?  I have a router hop
between my Ascend and I had to slow down port speed.

-----Original Message-----
From: Dave Joyce [mailto:Dave.Joyce@rtc1.com]
Sent: Tuesday, August 17, 1999 9:36 AM
To: Scot Tucker; phiber@polar.negation.net
Cc: ascend-users@bungi.com
Subject: Re: (ASCEND) Dial out Problem


I can dial out using a Max 2012 but it was a lot of jumping around until it
worked.

Now when we connect to a remote computer it will respond fine and then all
of a sudden just stop responding, maybe after 10 or so keystrokes, wait
about 15 seconds and you get to use another 10 or so keystrokes.

I was trying to use this outbound network modem to connect our accounting
people with the BBS banking system, but with the constant delays it is too
frustrating to use. It doesn't seem to be DeskDials fault as this symptom
occurs when in a direct telnet session doing the open command.

Is there anyone one has information on the solution or do we just scrap the
Max's for outbound calls?

Dave Joyce
Internet Manager
RTC on Line
219-223-0228
FAX 219-223-4898

----- Original Message -----
From: Scot Tucker <STUCKER@mvnhealth.com>
To: <phiber@polar.negation.net>
Cc: <ascend-users@bungi.com>
Sent: Tuesday, August 17, 1999 7:40 AM
Subject: Re: (ASCEND) Dial out Problem


> Our lines are configured for 2way; is there any thing else we can do?
>
> Scot Tucker - Networking Support
> Network Data Systems
> (315) 792-1057
> fax (315) 792-1070
> mailto:stucker@mvnhealth.com
>
> >>> Chris Rogers <phiber@polar.negation.net> 07/30/99 05:20PM >>>
> Is the T1/PRI circuit that the MAX is using a DID or 2way?  If its a DID,
> you will not be able to place out bound calls, and the MAX box wont
> exactly tell you that.  Hope this helps some,
>
> -chris
>
> On Fri, 30 Jul 1999, Scot Tucker wrote:
>
> > We have an ascend max 4002 and we can't dial out with it at all. When we
> > try to open a available modem ie ascend% open 3:1, we get the server
> > ready message with the port we're using. We can enter at commands and
> > get OK responces but when we try to dial out it doesn't work on any
> > modem. It doesn't even try to take the modem off hook.
> >
> > If someone could help, I would be very grateful. The Ascend Max 4k just
> > got a Ease of Setup award, but it hasn't been easy for us at all!
> >
> > Thank you
> >
> >
> > Scot Tucker - Networking Support
> > Network Data Systems
> > (315) 792-1057
> > fax (315) 792-1070
> > mailto:stucker@mvnhealth.com
> >
> > ++ Ascend Users Mailing List ++
> > To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> > To get FAQ'd: <http://www.nealis.net/ascend/faq>
> >
>
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <http://www.nealis.net/ascend/faq>
>
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <http://www.nealis.net/ascend/faq>

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>
++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>