Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: (ASCEND) Syslog Codes



Many Thanks Dean

IanC

Dean Frye wrote:
> 
> The important fields to know about are the disconnect cause and progress
> codes (the c= and p= numbers).
> 
> The chart is below:
> 
> Index   Disconnect Reason       Progress Type
> 
> 0       No Reason               No Progress
> 1       Not Applicable          Unknown
> 2       Unknown                 Unknown
> 3       Call Disconnected
> 4       CLID Authentication Failed
> 5       CLID Radius Timeout
> 10      Modem never detected DCD        Call Up
> 11      DCD detected but went inactive
> 12      Modem result codes parse fail
> 20      TermSrv - user quit
> 21      TermSrv - idle timeout
> 22      TermSrv - exit Telnet
> 23      TermSrv - no IP Addr
> 24      TermSrv - exit Raw TCP
> 25      TermSrv - login failed
> 26      TermSrv - Raw TCP disabled
> 27      TermSrv - CTRL-C during login
> 28      TermSrv - Destroyed
> 29      TermSrv - user closed VirtConn
> 30      TermSrv - VirtConn destroyed    Modem Up
> 31      TermSrv - exit Rlogin           Modem awaiting DCD
> 32      TermSrv - bad Rlogin option     Modem awaiting Codes
> 33      TermSrv - not enough resources
> 35      MPP - no NULL msg timeout
> 40      PPP - LCP Timeout               Terminal Server started
> 41      PPP - LCP Negotiation failed    Raw TCP started
> 42      PPP - PAP Auth failed           Telnet started
> 43      PPP - CHAP Auth failed          Raw TCP connected
> 44      PPP - Remote Auth failed                Telnet connected
> 45      PPP - Receive Terminate Req     Rlogin started
> 46      PPP - Receive Close Event               Rlogin connected
> 47      PPP - No NCP's were open
> 48      PPP - MP bundle unknown
> 49      PPP - LCP close MP add fail
> 50      Session Table Full              Modem Outdial - Call Up
> 51      Out of resources
> 52      Invalid IP Address
> 53      Hostname resolution failed
> 54      Bad/missing port number
> 60      Host Reset                      LAN Session Up
> 61      Connection refused              Opening LCP
> 62      Connection timeout              Opening CCP
> 63      Connection Closed               Opening IPNCP
> 64      Network unreachable             Opening BNCP
> 65      Host unreachable                LCP Opened
> 66      Network admin unreachable       CCP Opened
> 67      Host admin unreachable          IPNCP Opened
> 68      Port unreachable                        BNCP Opened
> 69                                      LCP State Initial
> 70                                      LCP State Starting
> 71                                      LCP State Closed
> 72                                      LCP State Stopped
> 73                                      LCP State Closing
> 74                                      LCP State Stopping
> 75                                      LCP State Request Sent
> 76                                      LCP State Ack Received
> 77                                      LCP State Ack Sent
> 80                                      IPXNCP Opened
> 81                                      ATNCP Opened
> 82                                      BACP Opening
> 83                                      BACP Opened
> 90                                      V110 Up
> 91                                      V110 State Opened
> 92                                      V110 State Carrier
> 93                                      V110 State Reset
> 94                                      V110 State Closed
> 100     Session Timeout
> 101     Invalid incoming user
> 102     Disconnect due to callback
> 120     Protocol disabled/unsupported
> 150     Disconnect requested by RADIUS
> 151     Disconnect by Local Admin
> 160     V110 timeout/sync retry exceed
> 170     PPP Auth Timeout exceeded
> 180     User executed Do..Hangup
> 185     Remote End Hung Up
> 190     Resource has been Quiesced
> 195     MAX Call duration reached
> 
> At 03:30 PM 4/16/98 +0100, you wrote:
> >Y'all
> >
> >Could someone tell me what the various fields in the following syslog
> >messages are:
> >
> >Conn=("INININ" ?->? PPP 12000/12000 60/11) Auth=(22 435/7 254/11)
> >Sess=(169 5039/96 24965/71)
> >
> >
> >call 81 CL 0K  u=01635899999 c=40 p=75 s=21600 r=28800
> 
> So the above call had an LCP timeout at the beginning of the negotiation.
> 
> Regards,
> 
> dean
> 
> >
> >I recognise the modem speeds and phone nos, but what are the rest?
> >
> >Are they documented?
> >
> >ta
> >
> >--
> >+------------------------------------------------------------------+
> >| Ian Cowley    Network Design Consultant                          |
> >|    mailto:icowley@x-lsil.com or mailto:yelwoci@x-compuserve.com  |
> >|        WWW     http://ourworld.compuserve.com/homepages/yelwoci  |
> >|                                                                  |
> >|ANTI SPAM STRIP x- FROM MAIL ADDRESS                              |
> >+------------------------------------------------------------------+
> >++ Ascend Users Mailing List ++
> >To unsubscribe:        send unsubscribe to ascend-users-request@bungi.com
> >To get FAQ'd:  <http://www.nealis.net/ascend/faq>
> >
> >
> -------------------------------------------------------------
> Dean Frye                                      +61.3.96567000
> Ascend Communications Australia                   0418 546635
> lvl 38/55 Collins St
> Melbourne VIC 3000
> Ascend Australia Support:             apac.support@ascend.com

-- 
+------------------------------------------------------------------+
| Ian Cowley    Network Design Consultant                          |
|    mailto:icowley@x-lsil.com or mailto:yelwoci@x-compuserve.com  | 
|        WWW     http://ourworld.compuserve.com/homepages/yelwoci  |
|                                                                  |
|ANTI SPAM STRIP x- FROM MAIL ADDRESS                              | 
+------------------------------------------------------------------+
++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>