Umm. If I understand you correctly you want to see the fatal errors? If so
this should point you in the right direction:
Go Full Access
Hit Cntrl-D, then hit D for Debug.
> fatal-history
OPERATOR RESET: Index: 99 Load: mhpt1m Revision: 4.6Cp15
Date: 03/21/1997. Time: 19:02:56
NVRAMCLEAR Reset from unknown in security profile 1.
If you want to look at all the debug commands type
> help ascend
Then you will get something like this:
> help ascend
? -> List all monitor commands
addrpool -> toggle addr pool debugs
arptable -> dump active ARP table entries
arpToggle -> Toggle ARP debug
avm -> show avail/dead modems
bridge-info -> display bridge address buckets
brouterDebug -> toggle brouter debug display
brouterLoad -> report brouter backlog time
brouterSave -> toggle brouter save info
callback -> Toggle callback debug output
callblocks -> show networki call blocks
callroute -> toggle callroute debug display
cbDumpList -> Dump the callback list
clockSource -> show the current clock source
clr-history -> Clear history log
ConnList -> Display connection list information
coreDump -> enable/disable coredumps over UDP, specify dump server
coreMsg -> toggle core debug display
ctCheck -> check CIDR tree
ctDebug -> toggle cidr tree debug display
< -- Hit [return] for next page, q [return] to end list -- >
ctGc -> schedule a cidr gc
dhcpToggle -> Toggle display of DHCP debug output
dumpBytes -> dumpbytes address length
dumpstackinfo -> Dump the Stack Info list
dumpWord -> Dump a single word of memory
ether-display -> ether-display <port #> <n>
ether-stats -> ether-stats <port #>
fatal-history -> List history log
fcat -> cat configuration from flash
fclear -> clear configuration from flash
FiltUpdate -> Request update of a connection
frdlState -> toggle frdlcall state display
frdump -> dump Frame Relay if table
frestore -> restore configuration from flash
frInArp -> Send FR Inverse Arp Test
frLinkState -> toggle for Frame Relay control messages
frlmi -> print Frame Relay lmi debug
frMgrdump -> dump Frame Relay Mgr table
frSCert -> toggle to different Cert
frState -> toggle for Frame Relay if messages
fsave -> save configuration to flash
heartbeat -> Toggle MULTICAST HEARTBEAT debug output
help -> List all monitor commands
ipAdrCfg -> monitor IP addr cfg actions
ippacket -> toggle ip packet parse display
ipRoutes -> toggle IP route manager debug display
ipxConn -> Display the IPX connection table
ipxSpoof -> toggle IPX spoofing debug display
lanval -> Enable messages in lanval module
lcState -> toggle lancore state display
leakpool -> dump leaky pool list
lifDebug -> toggle lif/L2/L3/ debug output
lpm -> toggle LPMOD debug
mcdDumpList -> Dump the max call duration list
mdbStr -> AT override string
mdialout -> Toggle MDIALOUT dbg
mdialsess -> Dump dialout sessions
modemDiag -> toggle modem diag debug display
modemdrvDump -> dump modem stats
modemdrvState -> toggle modemdrv debug display
mpEntry -> Dump MP Info table Entry
mppcm -> Toggle MPPCM debug output
Hope that helps.
Jason Nealis
Director Internet Operations
Internet Access
Erols Internet
On Wed, 17 Sep 1997, Dave Berzins wrote:
> Is there debug command in the command line interface that will show me why
> my max reboots, fatal errors etc? I thought there was but for the life of
> my I can't find it in the manual. HELP!
>
> Dave...
>
>
> Dave Berzins (berzins@nucleus.com)
> President, Nucleus Information Service Inc.
>
> 1835B 10 Avenue S.W., Calgary, Alberta, Canada, T3C 0K2
> Phone: (403)209-0000 Fax: (403)541-9474 Modem: (403)541-9400
> www: <A HREF="http://www.nucleus.com">http://www.nucleus.com</A>
>
> Nucleus is ... Everything Internet!
> ++ Ascend Users Mailing List ++
> To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
> To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>>
>
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>>
</PRE>
<!--X-MsgBody-End-->
<!--X-Follow-Ups-->
<!--X-Follow-Ups-End-->
<!--X-References-->
<HR>
<STRONG>References</STRONG>:
<UL>
<LI><STRONG><A HREF="msg08797.html">(ASCEND) DEBUG?</A></STRONG></LI>
<UL>
<LI><EM>From</EM>: Dave Berzins <berzins@nucleus.com></LI>
</UL>
</UL>
<!--X-References-End-->
<!--X-BotPNI-->
<HR>
<UL>
<LI>Prev by Date:
<STRONG><A HREF="msg08842.html">Re: (ASCEND) SNMP and OS?</A></STRONG>
</LI>
<LI>Next by Date:
<STRONG><A HREF="msg08804.html">(ASCEND) Aptiva 28.8 NO GO</A></STRONG>
</LI>
<LI>Prev by thread:
<STRONG><A HREF="msg08797.html">(ASCEND) DEBUG?</A></STRONG>
</LI>
<LI>Next by thread:
<STRONG><A HREF="msg08810.html">Re: (ASCEND) DEBUG?</A></STRONG>
</LI>
<LI>Index(es):
<UL>
<LI><A HREF="mail4.html#08805"><STRONG>Main</STRONG></A></LI>
<LI><A HREF="thrd167.html#08805"><STRONG>Thread</STRONG></A></LI>
</UL>
</LI>
</UL>
<!--X-BotPNI-End-->
<!--X-User-Footer-->
<!--X-User-Footer-End-->
</BODY>
</HTML>