Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: (ASCEND) Connection code 220 ?

At 02:35 PM 7/8/98 +0200, Andrey Bobyshev wrote:
>
>Hi,
>
>Does someone know what the connection code 220 means
>for a ppp session to MAX-4000 ? This code is NOT in the list 
>of codes described at the URL http://www.ascend.com/898.html,
>however I see a pretty high a number of sessions terminated 
>with this code.

Some new codes have been added - the docs will be updated, but in
the meantime:

>>Disconnect codes and their meanings
>>The following list displays Disconnect codes and their meanings:
>>Code Description
>>1    Not applied to any call.
>>2    Unknown disconnect.
>>3    Call disconnected.
>>4    CLID authentication failed.
>>5    RADIUS timeout during authentication.
>>6    Successful authentication. Ascend unit is configured to
>>     callback user.
>>7    Pre-T310 Send Disc timer triggered.
>>9    No modem is available to accept call.
>>10   Modem never detected Data Carrier Detect (DCD).
>>11   Modem detected DCD, but modem carrier was lost.
>>12   Ascend unit failed to successfully detect modem result codes.
>>13   Ascend unit failed to open a modem for outgoing call.
>>14   Ascend unit failed to open a modem for outgoing call
>>     while modemdiag diagnostic command is enabled.
>>20   User exited normally from the terminal server.
>>21   Terminal server timed out waiting for user input.
>>22   Forced disconnect when exiting telnet session.
>>23   No IP address available when invoking PPP or SLIP command.
>>24   Forced disconnect when exiting raw TCP session.
>>25   Exceeded maximum login attempts.
>>26   Attempt to start a raw TCP session, but raw TCP is disabled
>>     on Ascend unit.
>>27   Control-C characters received during login.
>>28   Terminal server session cleared ungracefully.
>>29   User closed a Terminal server virtual connect normally.
>>30   Terminal server virtual connect cleared ungracefully.
>>31   Exit from rlogin session.
>>32   Establishment of rlogin session failed because of bad options.
>>33   Ascend unit lacks resources to process terminal server request.
>>35   MP+ session cleared because no null MP packets received. An
>>     Ascend unit sends (and should receive) null MP packets
>>     throughout an MP+ session.
>>40   LCP timed out waiting for a response.
>>41   LCP negotiations failed, usually because user is configured to
>>     send passwords via PAP, and Ascend unit is configured to only
>>     accept passwords via CHAP (or vice versa).
>>42   PAP authentication failed.
>>43   CHAP authentication failed.
>>44   Authentication failed from remote server.
>>45   Ascend unit received Terminate Request packet while LCP
>>     was in open state.
>>46   Ascend unit received Close Request from upper layer,
>>     indicating graceful LCP closure.
>>47   Ascend unit cleared call because no PPP Network Core Protocols
>>     (NCPs) were successfully negotiated. Typically, there is no
>>     agreement on the type of routing or bridging that is supported
>>     for the session.
>>48   Disconnected MP session. The Ascend unit accepted a added
>>     channel, but cannot determine which call to which to add
>>     the new channel.
>>49   Disconnected MP call because no more channels can be added.
>>50   Telnet or raw TCP session tables full.
>>51   Ascend unit has exhausted Telnet or raw TCP resources.
>>52   For Telnet or raw TCP session, IP address is invalid.
>>53   For Telnet or raw TCP session, Ascend unit cannot resolve host name.
>>54   For Telnet or raw TCP session, Ascend unit received bad
>>     or missing port number.
>>60   For Telnet or raw TCP session, host reset.
>>61   For Telnet or raw TCP session, connection was refused.
>>62   For Telnet or raw TCP session, connection timed out.
>>63   For Telnet or raw TCP session, connection closed by foreign host.
>>64   For Telnet or raw TCP session, network unreachable.
>>65   For Telnet or raw TCP session, host unreachable.
>>66   For Telnet or raw TCP session, network admin unreachable.
>>67   For Telnet or raw TCP session, host admin unreachable.
>>68   For Telnet or raw TCP session, port unreachable.
>>100  Session timed out.
>>101  Invalid user.
>>102  Callback enabled.
>>115  Instigating call no longer active.
>>120  Requested protocol is disabled or unsupported.
>>150  Disconnect requested by RADIUS server.
>>151  Call disconnected by local administrator.
>>152  Call disconnected via SNMP.
>>160  Exceeded maximum amount of V.110 retries.
>>170  Timeout waiting to authenticate far end.
>>180  User disconnected by invoking Do Hangup from VT100 interface.
>>181  Call cleared by system.
>>185  Signal lost from far end, typically because the far end
>>     modem was turned off.
>>190  Resource has been quiesced.
>>195  Maximum duration time reached for call.
>>201  Ascend unit has low memory.
>>210  TNT modem card stops working while it has calls outstanding.
>>220  Ascend unit requires CBCP, but client does not support it.
>>230  Ascend unit deleted VROUTER.
>>240  Ascend unit disconnected call on the basis of LQM measurements.
>>
>>
>>
>>Progress codes and their meanings
>>The following list displays Progress codes and their meaning:
>>Code Description
>>1    Not applied to any call.
>>2    Unknown progress.
>>10   Ascend unit has detected and accepted call.
>>30   Ascend unit has assigned modem to call.
>>31   Modem is awaiting DCD from far-end modem.
>>32   Modem is awaiting result codes from far-end modem.
>>40   Terminal server session started.
>>41   Raw TCP session started.
>>42   Immediate Telnet session started.
>>43   Connection made to raw TCP host.
>>44   Connection made to Telnet host.
>>45   Rlogin session started.
>>46   Connection made with Rlogin session.
>>47   Terminal server authentication started.
>>50   Modem outdial session started.
>>60   LAN session is up.
>>61   Opening LCP.
>>62   Opening CCP.
>>63   Opening IPNCP.
>>64   Opening BNCP.
>>65   LCP opened.
>>66   CCP opened.
>>67   IPNCP opened.
>>68   BNCP opened.
>>69   LCP in initial state.
>>70   LCP in Initial state.
>>71   LCP in Starting state.
>>72   LCP in Closed state.
>>73   LCP in Stopped state.
>>74   LCP in Closing state.
>>75   LCP in Stopping state.
>>76   LCP in Req-Sent state.
>>77   LCP in Ack-Rcvd state.
>>78   LCP in Ack-Sent state.
>>80   IPX NCP in Open state.
>>81   AT NCP in Open state.
>>82   BACP being opened.
>>83   BACP is now open.
>>84   CBCP being opened.
>>85   CBCP is now open.
>>90   Ascend unit has accepted V.110 call.
>>91   V.110 call is in opened state.
>>92   V.110 call is in carrier state.
>>93   V.110 call is in reset state.
>>94   V.110 call is in closed state.
>>100  Ascend unit determines that call requires callback.
>>101  Authentication failed.
>>102  Remote authentication server timed out.
>>120  Frame relay link is inactive. Negotiations are in progress.
>>121  Frame relay link is active and has end-to-end connectivity.


Kevin Smith			Ascend Communications...
Customer Satisfaction	...where Network Solutions never end.

++ Ascend Users Mailing List ++
To unsubscribe:	send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd:	<http://www.nealis.net/ascend/faq>
Follow-Ups: References: