Helo TNT gurus,
Need your help on the following settings :
1) Shall we know what this any-shelf slot entires ?
admin> dir ip-interface
11 09/11/1997 10:10:20 { { shelf-1 slot-2 1 } 0 }
11 09/11/1997 10:10:20 { { shelf-1 slot-2 2 } 0 }
11 09/11/1997 10:10:20 { { shelf-1 slot-2 3 } 0 }
11 09/11/1997 10:10:20 { { shelf-1 slot-2 4 } 0 }
11 09/11/1997 10:43:49 { { shelf-1 slot-2 5 } 0 }
22 09/11/1997 10:15:06 { { shelf-1 controller 1 } 0 }
10 09/11/1997 10:43:49 { { any-shelf slot-1 0 } 0 }
11 09/11/1997 10:43:49 { { any-shelf slot-1 2 } 0 }
11 09/11/1997 10:43:49 { { any-shelf slot-1 3 } 0 }
11 09/11/1997 10:43:49 { { any-shelf slot-1 4 } 0 }
19 09/11/1997 10:43:49 { { any-shelf slot-2 0 } 0 }
20 09/11/1997 10:43:49 { { any-shelf slot-2 2 } 0 }
20 09/11/1997 10:43:49 { { any-shelf slot-2 3 } 0 }
20 09/11/1997 10:43:49 { { any-shelf slot-2 4 } 0 }
29 09/11/1997 10:43:50 { { any-shelf any-slot 0 } 0 }
2) Is it must to set enabled =no in all the other ether ports
expect connected one. We are doing it now.
admin> dir ether
5 09/11/1997 10:43:50 { shelf-1 controller 1 }
8 09/11/1997 10:43:50 { shelf-1 slot-2 1 }
8 09/11/1997 10:43:50 { shelf-1 slot-2 2 }
8 09/11/1997 10:43:50 { shelf-1 slot-2 3 }
8 09/11/1997 10:43:50 { shelf-1 slot-2 4 }
8 09/11/1997 10:43:50 { shelf-1 slot-2 5 }
3 09/11/1997 10:43:50 { any-shelf any-slot 0 }
4 09/11/1997 10:43:50 { any-shelf slot-1 0 }
5 09/11/1997 10:43:50 { any-shelf slot-1 2 }
5 09/11/1997 10:43:50 { any-shelf slot-1 3 }
5 09/11/1997 10:43:50 { any-shelf slot-1 4 }
3) When we are changing ether ports for eg. changing of active ether port
from 10baseT to 100BaseT is it necessary to reset TNT.
4) In one of TNT Unit we are facing problem with 100BaseT.
Here's the configuration:
admin> read ip-inter {{ 1 2 5}0}
IP-INTERFACE/{ { shelf-1 slot-2 5 } 0 } read
admin> list
interface-address* = { { shelf-1 slot-2 5 } 0 }
ip-address = 10.10.90.10/24
proxy-mode = Off
rip-mode = routing-off
route-filter = ""
rip2-use-multicast = yes
ospf = { no 0.0.0.0 normal 10 40 5 simple ascend0 1 16777215 type-1 c0:00:00:00+
multicast-allowed = no
multicast-rate-limit = 100
atmp = { atmp-disabled atmp-home-agent-router 0 "" no }
admin> read ether {1 2 5}
ETHERNET/{ shelf-1 slot-2 5 } read
admin> list
interface-address* = { shelf-1 slot-2 5 }
link-state = up
link-state-enabled = no
enabled =yes
ether-if-type = utp
yes , all the other ether ports enabled= no.
using the above setting we can able to ping to 100BaseT Ether port
We can't able to ping to gateway.
The gateway setting is :
name* = default
dest-address = 0.0.0.0/0
gateway-address = 10.10.90.1
metric = 1
cost = 1
preference = 60
third-party = no
ase-type = type-1
ase-tag = c0:00:00:00
private-route = yes
active-route = yes
ase7-adv = N/A
The same gateway setting we are using for 10Baset , no problem.
When set debug is on we can manage to see the
arp table entries of same segment ether addresses, but
can't ping to them.
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <<A HREF="http://www.nealis.net/ascend/faq">http://www.nealis.net/ascend/faq</A>>
</PRE>
<!--X-MsgBody-End-->
<!--X-Follow-Ups-->
<!--X-Follow-Ups-End-->
<!--X-References-->
<!--X-References-End-->
<!--X-BotPNI-->
<HR>
<UL>
<LI>Prev by Date:
<STRONG><A HREF="msg08635.html">(ASCEND) 56k on DMS 10</A></STRONG>
</LI>
<LI>Next by Date:
<STRONG><A HREF="msg08633.html">Re: (ASCEND) 5.0ap24</A></STRONG>
</LI>
<LI>Prev by thread:
<STRONG><A HREF="msg08632.html">(ASCEND) MAXTNT Filter Problem</A></STRONG>
</LI>
<LI>Next by thread:
<STRONG><A HREF="msg08635.html">(ASCEND) 56k on DMS 10</A></STRONG>
</LI>
<LI>Index(es):
<UL>
<LI><A HREF="mail11.html#08634"><STRONG>Main</STRONG></A></LI>
<LI><A HREF="thrd161.html#08634"><STRONG>Thread</STRONG></A></LI>
</UL>
</LI>
</UL>
<!--X-BotPNI-End-->
<!--X-User-Footer-->
<!--X-User-Footer-End-->
</BODY>
</HTML>