Ascend Archive
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: (ASCEND) Can a p130 handle a full t1?
At 06:37 PM 9/24/97 -0400, Craig Salmond wrote:
>On Wed, 24 Sep 1997, Josh Beck wrote:
>
>> > Cool.. How did you statically route to a specific DLCI with the
>> > Pipeline, with the cisco I just created sub interfaces??
>>
>> Two connection profiles, one default route (customer to us)
>> another route (LAN network block of customers other location) via the ip
>> address of the remote side of the customer<->pvc. We used 10.* addresses
>> for grins. Here are the routes and addresses from one P130:
> Way Cool. Nothing like creative routing to get the job done.
>However I still don't think there is a way to do the following:
>
>T1 FR on a P130 DCLI 25
>
>128K FR DCLI 26 to some destination
>256K FR DCLI 27 to some destination
>64K FR DCLI 28 to some destination
I have a partial *test* setup which shows that part of this can be done. Note
this was a TEST setup, and has been fiddled with a few times, so please
excuse any inconsistencies that may appear here. It did work at the time ;)
You just rely on the frame-relay switch to control the CIR values:
START=FRELAY=200=0
Name=frame-1
Active=Yes
Nailed Grp=3
Data Svc=64K
Link Mgmt=T1.617D
END=FRELAY=200=0
START=ROUTE=200=0
Name=Default
Gateway=192.207.23.93
Metric=1
Private=Yes
END=ROUTE=200=0
START=CONN=200=1
Station=max-house
Active=Yes
Dial #=1700nnnnnnn
Route IP=Yes
Bridge=No
Encaps options...Send Auth=CHAP
Encaps options...Send PW=xxxxxxxx
Ip options...LAN Adrs=192.207.23.93/24
END=CONN=200=1
START=CONN=200=2
Station=dlci-16
Active=Yes
Encaps=FR
Route IP=Yes
Bridge=No
Encaps options...FR Prof=frame-1
Ip options...LAN Adrs=10.0.0.16/32
Telco options...Call Type=Nailed
END=CONN=200=2
START=CONN=200=3
Station=dlci-17
Active=Yes
Encaps=FR
Route IP=Yes
Bridge=No
Encaps options...FR Prof=frame-1
Encaps options...DLCI=17
Ip options...LAN Adrs=10.0.0.17/32
Telco options...Call Type=Nailed
END=CONN=200=3
START=Nailed T1=300=0
Last DS0 =24
END=Nailed T1=300=0
START=ETHERNET=200=0
Ether options...IP Adrs=10.20.10.174/16
Ether options...RIP=Off
Bridging=No
NAT Routing=Yes
NAT Profile=max-house
Log...Syslog=Yes
Log...Log Host=10.20.10.172
END=ETHERNET=200=0
START=SYSTEM=0=0
Name=kevin
END=SYSTEM=0=0
START=LINE=100=0
Name=Factory
Switch Type=NI-1
Line 1...Link Type=Multi_P
Line 1...Pri Num=3758
Line 1...Pri SPID=41568237580101
Line 1...Sec Num=3761
Line 1...Sec SPID=41568237610101
END=LINE=100=0
START=LINE=100=1
END=LINE=100=1
Kevin
++ Ascend Users Mailing List ++
To unsubscribe: send unsubscribe to ascend-users-request@bungi.com
To get FAQ'd: <http://www.nealis.net/ascend/faq>
References: