Well, I hope it is not coincidence... I propped the DSL router up and speeds
started creeping up (per dslreports and Qwest speed tests) until about 15
minutes later it was back at the max.  It's been quite awhile now and still
working at max.  So after many years of use (9+), it decides to get temp
sensitive!?  Perhaps it is the EOL you mentioned...


-----Original Message-----
From: tclug-list-bounces at mn-linux.org
[mailto:tclug-list-bounces at mn-linux.org] On Behalf Of Justin Krejci
Sent: Thursday, July 22, 2010 4:12 AM
To: TCLUG Mailing List
Subject: Re: [tclug-list] How detect what's using Internet connection?

What version of code are you running? Maybe a newer version could help.

Check "show errors" and also look at the eth interface stats for various
error counters on the cisco.

Additionally some models of the 67x (you didn't mention which you have) get
very hot on their own so if you have it in an already warm room with minimal
air flow it could be overheating and nearing the end of its life. If this
seems like the case then try propping it up so the bottom is more accessible
to some air flow. 
You could check the cable from the Cisco, try replacing it with another
cable. Is it going to a switch? Try another switch port. Basic things like
that can sometimes identify/eliminate during troubleshooting and are super
easy to try.

Sent via BlackBerry from T-Mobile

-----Original Message-----
From: "Jeff Jensen" <jjensen at apache.org>
Sender: tclug-list-bounces at mn-linux.org
Date: Wed, 21 Jul 2010 23:36:07 
To: 'TCLUG Mailing List'<tclug-list at mn-linux.org>
Reply-To: TCLUG Mailing List <tclug-list at mn-linux.org>
Subject: [tclug-list] How detect what's using Internet connection?

Lately I've had a lot of slowdown with my DSL router.  None of the machines
appear to be downloading, streaming, etc. (they could be, but didn't look
like it to me).  For example, at the moment, pinging the router:

PING dslrouter (10.0.0.1) 56(84) bytes of data.
64 bytes from dslrouter (10.0.0.1): icmp_seq=1 ttl=64 time=1686 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=2 ttl=64 time=1326 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=3 ttl=64 time=1163 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=4 ttl=64 time=762 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=5 ttl=64 time=992 ms
^C
--- dslrouter ping statistics ---
6 packets transmitted, 5 received, 16% packet loss, time 5488ms
rtt min/avg/max/mdev = 762.641/1186.396/1686.273/312.092 ms, pipe 2


After I reboot it, it's back to sub-millisecond time.  But after a short
while, it's back up there.  It's really slowing down even casual surfing,
and the wife keeps yelling at me about it!  :-/


And then sometimes, like now, it is back to normal (but it was slow response
for awhile, maybe an hour or more?):

PING dslrouter (10.0.0.1) 56(84) bytes of data.
64 bytes from dslrouter (10.0.0.1): icmp_seq=1 ttl=64 time=0.811 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=2 ttl=64 time=0.862 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=3 ttl=64 time=0.873 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=4 ttl=64 time=0.841 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=5 ttl=64 time=0.810 ms
64 bytes from dslrouter (10.0.0.1): icmp_seq=6 ttl=64 time=0.830 ms
^C
--- dslrouter ping statistics ---
6 packets transmitted, 6 received, 0% packet loss, time 5225ms
rtt min/avg/max/mdev = 0.810/0.837/0.873/0.044 ms


How do I detect what is happening at the time of high load?
It is a Cisco CBOS DSL router.  I've been trying some CBOS show commands and
wondering about either Linux or Windows commands/apps to use?



_______________________________________________
TCLUG Mailing List - Minneapolis/St. Paul, Minnesota
tclug-list at mn-linux.org
http://mailman.mn-linux.org/mailman/listinfo/tclug-list
_______________________________________________
TCLUG Mailing List - Minneapolis/St. Paul, Minnesota
tclug-list at mn-linux.org
http://mailman.mn-linux.org/mailman/listinfo/tclug-list