The problem is, almost everything is onboard, so I can't move it around. I don't think it's an IRQ problem anyway, I think it's due to lack of power. I read about someone else having the same problem with their Athlon 1.4, and they stuck in a bigger power supply and it was fine. > -----Original Message----- > From: Hvidsten, Leif [mailto:hvidsl at parknicollet.com] > Sent: Friday, November 09, 2001 10:25 AM > To: 'tclug-list at mn-linux.org' > Subject: RE: [TCLUG] irq conflicts!!! > > > > Your motherboard manual should say which PCI slots share > IRQs. That way you can put your card(s) in the PCI slot(s) > that won't share IRQs to eliminate possible conflicts. For > example, my IWill KK266-R (KT133A chipset) is set up so that > AGP/PCI 1/PCI 5 share an IRQ, PCI 2/PCI 6 share an IRQ, PCI > 3/on-board sound share, and PCI 4/on-board RAID controller > share. This setup will vary greatly from mobo to mobo....my > Abit KT7A-RAID I used to have (based on the same KT133A > chipset) was setup differently. I can see which IRQs the > particular PCI card or on-board device will take within the > BIOS menus. In one of the menus it will list something like > USB Controller taking IRQ 11, Multimedia card taking IRQ 5, > etc..(because I forced it to that IRQ in the BIOS). One > other tip, especially when you have USB and a HighPoint > controller enabled, is to disable in the BIOS whatever you > don't need. Do you need the LPT/parallel printer port > enabled? Disabling will usually free up IRQ 7. ! Do you > need your serial ports? Disabling both will free up IRQ's 3 > and 4, if I remember correctly. Forcing PCI slots to take > certain IRQs may help as well, if offered in your BIOS. > > > > If you are not using the HighPoint controller you can > disable it and > > save irq 10. You can also try to put the tv tuner in > another pci slot. > > * Austad, Jay (austad at marketwatch.com) wrote: > > > Ok, I'm trying to set up my new Soyo Dragon+ board, and the > > ESCD bios crap > > > gives me the following devices on the following IRQ's: > > > > > > Multimedia Device 10 > > > Multimedia Device 10 > > > Mass Storage Cntrlr 10 > > > > > > > > > Multimedia Device 11 > > > USB 11 > > > USB 11 > > > USB 11 > > > Network 11 > > > Display 11 > > > > > > > > > > > > How do I fix this? The only card I have installed is a TV > > card and a > > > Geforce2 in the AGP slot. Otherwise, everything else is > > onboard. Normally > > > I wouldn't care, but the system locks during my Mandrake install. > > > > > > Jay > > > _______________________________________________ > > > Twin Cities Linux Users Group Mailing List - > > Minneapolis/St. Paul, Minnesota > > > http://www.mn-linux.org > > > tclug-list at mn-linux.org > > > https://mailman.mn-linux.org/mailman/listinfo/tclug-list > > > > > Spencer Butler > > Twin Cities Open Systems > > http://tcos.stderr.net > > 6126368989 at voicestream.net > > > > PRIVACY NOTICE: This e-mail message, including any > attachments, is for the sole use of the intended recipient(s) > and may contain business confidential and privileged > information. Any unauthorized review, use, disclosure or > distribution is prohibited. If this e-mail was not intended > for you, please notify the sender by reply e-mail that you > received this in error. Destroy all copies of the original > message and attachments. > > _______________________________________________ > Twin Cities Linux Users Group Mailing List - Minneapolis/St. > Paul, Minnesota http://www.mn-linux.org > tclug-list at mn-linux.org > https://mailman.mn-> linux.org/mailman/listinfo/tclug-list >